Adult Chat Room Your Alternative to Success
Page 189 (3) Remove the two CR frame springs and two screws of the TAPTITE CUP B M3x10, and clear away the CR frame. 3) Remove the two screws of the TAPTITE CUP S M3x6 and eliminate the MJ PCB ASSY from the MJ Lower frame. 9.14 Carriage PCB ASSY Tip When the Head/carriage device has not been eliminated, refer to “9.3 Head Joint Rubber / CR Timing Belt / Head/Carriage Unit” in this chapter to get rid of the Carriage PCB ASSY from the Head/carriage unit. 9.15 Ink refill ASSY Tip When the Head/carriage device has not been taken out, refer to “9.3 Head Joint Rubber / CR Timing Belt / Head/Carriage Unit” in this chapter to eliminate the Ink provide tubes from the Head/carriage device. The CO or FXS senses the ring floor and then grounds the suggestion direct to allow the PBX or FXO know that it is ready to acquire the incoming call.
4) Remove the USB floor plate. 2) Remove the Power harness from the Lower include. Page 178 Assembling Note When setting up the Power supply protect, insert the element that bends to the outdoors of the still left stop under the stopper of the Lower electric power supply frame, insert the entrance finish into the Lower electrical power provide frame rib, and repair the top rated slits in put by locking the Lower ability provide frame. 9.16 Ink Absorber Box / Ink Absorber Felt (For Ink Refill ASSY) Note Do not eliminate the Ink absorber box except if it requires to be replaced. 059L) Assembling Note Make certain that the Release levers L/R are on your aspect. Page 186 Encoder strip guard movie (4) On the proper conclusion of the CR body, press the rear end of the Guard film spring inward and Best-sex-chat release the remaining and right stop of the Encoder strip guard movie from the hook. 2) Release the hook, elevate up the front conclude of the Flushing box, and eliminate the Flushing box. 1) Remove the MJ PCB flat cable spacer. 2) Remove the Carriage flat cable from the Lower cover collectively with the Flat main. Remove it immediately after aligning the correct stop sq. opening with the boss-shape of the strip help.
5) Rotate the Encoder strip guard movie in the course of the arrow proven underneath. 2) Rotate the CR encoder strip in the route of the arrow revealed underneath. 4) To find 1 of the routine maintenance mode features shown on the subsequent page, use the numerical keys to directly input the routine maintenance mode you want to use. 2) To pick one of the maintenance mode features, right specify the servicing mode you want to use. 1) If the Ink refill ASSY consists of ink, use a Ink extraction syringe to extract the ink. 2) Remove the MJ PCB ASSY and Freeprivatesexcams.Com the MJ lessen frame from the Lower cover. 2) Remove the Carriage motor harness wiring. 9.19 Carriage Motor ASSY (1) Remove the manager via the opening on the Tube assistance plate by applying a flathead screwdriver, and then take away the Tube aid plate from the Lower include, sliding it to the left. Page 190 (4) Remove the two screws of the SCREW BIND M3x6 from the CR body, and eliminate the Carriage motor and Motor bracket from the CR body. 9.20 Flushing Base / Flushing Box (1) Remove the Flushing base. IF YOU Replace THE INK ABSORBER BOX OR FLUSHING BOX 5.1 Reset Purge and Flushing Counts (Maintenance mode 80) None Reset Purge and Flushing Counts (Maintenance method 80) Refer to “1.12 Reset Purge and Flushing Counts (Maintenance mode 80)” in this chapter for information on the execution.
1) Pull out the primary Drain tube and Air vent tube from the Ink absorber box. 6) Remove the Power supply shield from the Lower electrical power supply frame lock and the two stopper sections then pull it in the direction of you. 9.13 Power Supply PCB ASSY (1) Remove the screw of the TAPTITE CUP B M3x10 and the screw of the TAPTITE CUP S M3x6. 9.12 MJ PCB ASSY (1) Remove the two screws of the TAPTITE CUP B M3x10 and the screw of the TAPTITE CUP S M3x6, and then eliminate the MJ higher body. Page 177 (4) Remove the one particular screw of the SCREW PAN (WASHER) M4x8 DB from the Power wire holder. 5) Remove the Power twine from the Cable guide. The pair accused British ministers and officials of taking part in their illegal abduction, kidnapping and removal to Libya in March 2004, although Gaddafi was nonetheless in electricity. Look at the redacted portion of what I said. That thirty day period, other companies, together with Google, expressed desire in shopping for a portion of Facebook. Page 230 (6) Upon completion of scanning, the equipment displays the “Write Head Calib” on the Lcd, makes the head calibration facts, and writes it into the flash ROM on the most important PCB.
Leave a Reply