Delhi Call Girls Blogs | Free Escorts Blog Posting Classified Site

Page 189 (3) Remove the two CR frame springs and two screws of the TAPTITE CUP B M3x10, and get rid of the CR frame. 3) Remove the two screws of the TAPTITE CUP S M3x6 and clear away the MJ PCB ASSY from the MJ Lower body. 9.14 Carriage PCB ASSY Tip When the Head/carriage device has not been taken off, refer to “9.3 Head Joint Rubber / CR Timing Belt / Head/Carriage Unit” in this chapter to take out the Carriage PCB ASSY from the Head/carriage device. 9.15 Ink refill ASSY Tip When the Head/carriage unit has not been taken out, refer to “9.3 Head Joint Rubber / CR Timing Belt / Head/Carriage Unit” in this chapter to take out the Ink supply tubes from the Head/carriage unit. The CO or FXS senses the ring floor and then grounds the tip lead to permit the PBX or FXO know that it is prepared to receive the incoming phone.

4) Remove the USB ground plate. 2) Remove the Power harness from the Lower protect. Page 178 Assembling Note When setting up the Power source defend, insert the portion that bends to the outdoors of the left stop less than the stopper of the Lower electrical power supply body, insert the entrance end into the Lower power supply frame rib, and take care of the top slits in place by locking the Lower power offer frame. 9.16 Ink Absorber Box / Ink Absorber Felt (For Ink Refill ASSY) Note Do not clear away the Ink absorber box unless of course it requires to be replaced. 059L) Assembling Note Make absolutely sure that the Release levers L/R are on your aspect. Page 186 Encoder strip guard film (4) On the suitable conclude of the CR body, push the rear end of the Guard movie spring inward and release the still left and right stop of the Encoder strip guard movie from the hook. 2) Release the hook, raise up the front conclude of the Flushing box, and eliminate the Flushing box. 1) Remove the MJ PCB flat cable spacer. 2) Remove the Carriage flat cable from the Lower go over together with the Flat main. Remove it soon after aligning the appropriate close sq. opening with the boss-shape of the strip assist.

5) Rotate the Encoder strip guard film in the direction of the arrow demonstrated down below. 2) Rotate the CR encoder strip in the path of the arrow revealed below. 4) To select just one of the servicing mode capabilities proven on the pursuing webpage, use the numerical keys to immediately input the maintenance mode you want to use. 2) To pick out just one of the routine maintenance mode functions, specifically specify the routine maintenance mode you want to use. 1) If the Ink refill ASSY incorporates ink, use a Ink extraction syringe to extract the ink. 2) Remove the MJ PCB ASSY and the MJ reduce body from the Lower address. 2) Remove the Carriage motor harness wiring. 9.19 Carriage Motor ASSY (1) Remove the boss as a result of the opening on the Tube help plate by applying a flathead screwdriver, and then take out the Tube guidance plate from the Lower protect, sliding it to the left. Page one hundred ninety (4) Remove the two screws of the SCREW BIND M3x6 from the CR body, and take away the Carriage motor and Motor bracket from the CR frame. 9.20 Flushing Base / Flushing Box (1) Remove the Flushing foundation. IF YOU Replace THE INK ABSORBER BOX OR FLUSHING BOX 5.1 Reset Purge and Flushing Counts (Maintenance method 80) None Reset Purge and Free private Sex cams Flushing Counts (Maintenance manner 80) Refer to “1.12 Reset Purge and Flushing Counts (Maintenance manner 80)” in this chapter for particulars on the execution.

1) Pull out the most important Drain tube and Air vent tube from the Ink absorber box. 6) Remove the Power source defend from the Lower power provide body lock and the two stopper components then pull it toward you. 9.13 Power Supply PCB ASSY (1) Remove the screw of the TAPTITE CUP B M3x10 and the screw of the TAPTITE CUP S M3x6. 9.12 MJ PCB ASSY (1) Remove the two screws of the TAPTITE CUP B M3x10 and the screw of the TAPTITE CUP S M3x6, and then eliminate the MJ upper body. Page 177 (4) Remove the a person screw of the SCREW PAN (WASHER) M4x8 DB from the Power wire holder. 5) Remove the Power cord from the Cable information. The pair accused British ministers and officials of participating in their unlawful abduction, kidnapping and removing to Libya in March 2004, when Gaddafi was nevertheless in electricity. Look at the redacted part of what I reported. That thirty day period, other providers, like Google, expressed fascination in purchasing a part of Facebook. Page 230 (6) Upon completion of scanning, the machine displays the “Write Head Calib” on the Lcd, makes the head calibration knowledge, and writes it into the flash ROM on the main PCB.